Donde comprar el mando a distancia de la llave

[hps2005]

Como conseguir un mejor ajuste de los botones del mando a distancia dentro de la carcasa de la llave con espadín plegable:

Si metemos el mando de una llave original toyota dentro de la carcasa con espadin plegable, viendo exteriormente la carcasa con los botones, observamos un mal ajuste de los botones (sobre todo del de cerrar las puertas): ver foto


Con el repuesto para reparar los botones del mando a distancia (puse un post) se consigue un mejor ajuste. Al ser una lamina plastica independiente del mando a distancia, los milimetros de holgura que tiene el mando de mal ajuste con los agujeros de la carcasa quedan corregidos, consiguiendo una mejor apariencia estetica. Ver foto (la chapa metalica de la carcasa delata que la foto la hice dentro del corola, en el asiento del acompañante.

[hps2005]

Por cierto, me llego la ññave usada, por unos 14€ totales, pero no consigo reprogramarlo para que le sirva a mi coche. Alguien me puede echar una mano??????
Gracias

[hps2005]

Según el hilo de "Dipri", este es el proceso:
Yo lo estoy intentando, pero no se programa el mando a distancia, aunque si me arranca el coche.

Este es el texto del hilo que menciono:

I have the same problem, I have an Avensis 2.0D T3-X 2004. I've managed to purchase a blank key (736670-A) and also a remote fob on ebay. The blank key was £20 (quite rare) and the new remote fob £6.50 (more common, lots of used keys for sale). I've been told I can get the blank cut at my local locksmiths. I found these instuctions on the web for programming the fob for a Prius. It appears identical to less detailed instructions I found for an Avensis posted on this forum. I haven't tried this yet. I'll let you know if this works.

"Programming New Keys"

STEPS:
1. Begin by sitting in the driver seat with all the doors shut.
2. Insert your working master (black) key in the ignition.
3. Very Quickly, turn the key from "LOCK" to "ON" 5 times. (You will end with the key in the "LOCK" position)
4. Immediately, open and close the driver door 6 times very quickly. (End with the door closed)
5. Immediately, remove your working Master Key and insert your new Master Key
6. Turn the key to the "ON" position and leave it there while you wait for 1 minute.
7. After the minute, if you want to program another key, just remove the first one and insert the next one, turning it to "ON" and leaving it in position for 1 minute.
8. When you are through programming keys, just take the last one out, open and then close the driver door to lock in the programming, and your done

Programming Sub Keys (Grey) is done the same way except you turn the master key 4 times before you open and close the door 5 times. Then insert the sub key, turn to the "ON" position, and wait your minute. Finish by removing the key and opening and closing the door 1 time as before.

You can erase all the keys and start over by turning a working master key 6 times and then opening and closing the door 7 times. Then remove the key and reprogram again.

Remember : You only have a few seconds to perform each maneuver so don't waste time. You will know when you have done it right when you insert the blank key and the security light on the radio stops blinking. If it does not work, try completing the sequence faster, time yourself. And don't worry, if it doesn't work the first time, just do it again
**It is our understanding, according to the book, you can have 2 master keys and 1 sub key, however, we are aware of one gentleman who was able to program 4 masters and 2 subs. We currently have 3 masters and 1 sub.**